Design and test of SX-FEL cavity BPM

YUAN Ren-Xian; ZHOU Wei-Min; CHEN Zhi-Chu; YU Lu-Yang; WANG Bao-Pen; LENG Yong-Bin

doi:10.1088/1674-1137/37/11/118001

Chinese Physics C> 2013, Vol. 37> Issue(11) : 118001 DOI: 10.1088/1674-1137/37/11/118001

Design and test of SX-FEL cavity BPM

Abstract
HTML
Reference
Related

PDF

Abstract：
This paper reports the design and cold test of the cavity beam position monitor (CBPM) for SX-FEL to fulfill the requirement of beam position measurement resolution of less than 1 u m,even 0.1 u m. The CBPM was optimized by using a coupling slot to damp the TM₀₁₀ mode in the output signal. The isolation of TM₀₁₀ mode is about 117 dB,and the shunt impedance is about 200Ω@4.65 GHz with the quality factor 80 from MAFIA simulation and test result. A special antenna was designed to load power for reducing excitation of other modes in the cavity. The resulting output power of TM₁₁₀ mode was about 90 mV/mm when the source was 6 dBm,and the accomplishable minimum voltage was about 200 uV. The resolution of the CBPM was about 0.1u m from the linear fitting result based on the cold test.

References

[1]

Johnson R et al. Cavity BPMs for the NLC. SLAC-PUB-9211,2002[2] Walston S et al. Performance of a High Resolution Cavity Beam Position Monitor System. SLAC-PUB-12492,2007[3] Maesaka H,Inoue S et al. Development of the RF Cavity BPM of XFEL/Spring-8 DIPAC09,2009[4] CHU J H. Development of a C-band Cavity BPM and RF Electronics (Doctoral Thesis). Shanghai: Shanghai Institute of Applied Physics,2008(in Chinese)[5] LUO J. Research of a Cavity BPM System (Doctoral Thesis). Hefei: University of Science and Technology of China,2008(in Chinese)

[1]	Li Tang , Liang Liu , Ying Wu . Null test of cosmic curvature using deep learning method. Chinese Physics C, 2026, 50(2): 1-8.
[2]	Wen-Wen Ge , You-Jin Yuan , Jian-Cheng Yang , S. Litvinov , Geng Wang , Rui-Jiu Chen , Xin-Liang Yan , Hang Ren , Guo-Dong Shen . Design optimization of isochronous mode in the HIAF-SRing. Chinese Physics C, 2025, 49(12): 124001. doi: 10.1088/1674-1137/adcf0e
[3]	ZHANG Zhou-Li , HE Yuan , ZHANG Bin , LI De-Run , SHI Ai-Min , PAN Gang , DU Xiao-Nan , SUN Lie-Peng . Study of influence of radial matcher section end shape on RFQ cavity frequency. Chinese Physics C, 2014, 38(7): 077007. doi: 10.1088/1674-1137/38/7/077007
[4]	ZHANG Cong , HE Yuan , ZHAO Hong-Wei , ZHANG Sheng-Hu . Multipacting simulation and analysis of a taper quarter wave cavity by using Analyst-PT3P. Chinese Physics C, 2012, 36(4): 362-366. doi: 10.1088/1674-1137/36/4/012
[5]	XU Ji-Lei , GUAN Meng-Yun , YANG Chang-Gen , WANG Yi-Fang , ZHANG Jia-Wen , LU Chang-Guo , Kirk McDonald , Robert Hackenburg , Kwong Lau , Logan Lebanowski , Cullen Newsom , Lin Shih-Kai , Jonathan Link , MA Lie-Hua , Viktor Pec , Vit Vorobel , CHEN Jin , LIU Jin-Chang , ZHOU Yong-Zhao , LIANG Hao . Design and preliminary test results of Daya Bay RPC modules. Chinese Physics C, 2011, 35(9): 844-850. doi: 10.1088/1674-1137/35/9/011
[6]	PENG Quan-Ling , SUN Jian , ZHAO Guang-Yuan , SHI Cai-Tu . Principle and Software Design of Helmhotz Coil Measurement System. Chinese Physics C, 2001, 25(9): 920-925.
[7]	WANG Man , LI Jin , CUI Xiang-Zong , XIA Xiao-Mi , LAI Yuan-Fen , YAO Xiao-Guang . PROTOTYPE OF END CAP SHOWER COUNTERAND ITS BEAM TEST. Chinese Physics C, 1987, 11(3): 321-326.

Access

Get Citation

YUAN Ren-Xian, ZHOU Wei-Min, CHEN Zhi-Chu, YU Lu-Yang, WANG Bao-Pen and LENG Yong-Bin. Design and test of SX-FEL cavity BPM[J]. Chinese Physics C, 2013, 37(11): 118001. doi: 10.1088/1674-1137/37/11/118001

RIS(for EndNote,Reference Manager,ProCite)

BibTex

Txt

Milestone

Received: 2013-01-07
Revised: 1900-01-01

Article Metric

Article Views(3077)
PDF Downloads(221)
Cited by(0)

Policy on re-use

To reuse of subscription content published by CPC, the users need to request permission from CPC, unless the content was published under an Open Access license which automatically permits that type of reuse.

通讯作者: 陈斌, bchen63@163.com

1.
沈阳化工大学材料科学与工程学院沈阳 110142

Design and test of SX-FEL cavity BPM

Corresponding author: YUAN Ren-Xian,

Received Date: 2013-01-07
Accepted Date: 1900-01-01
Available Online: 2013-11-05

Abstract: This paper reports the design and cold test of the cavity beam position monitor (CBPM) for SX-FEL to fulfill the requirement of beam position measurement resolution of less than 1 u m,even 0.1 u m. The CBPM was optimized by using a coupling slot to damp the TM₀₁₀ mode in the output signal. The isolation of TM₀₁₀ mode is about 117 dB,and the shunt impedance is about 200Ω@4.65 GHz with the quality factor 80 from MAFIA simulation and test result. A special antenna was designed to load power for reducing excitation of other modes in the cavity. The resulting output power of TM₁₁₀ mode was about 90 mV/mm when the source was 6 dBm,and the accomplishable minimum voltage was about 200 uV. The resolution of the CBPM was about 0.1u m from the linear fitting result based on the cold test.